|   alkyd paint rana   |   No comment
رنگ ضد حریق


  Product information 

1-Good weather resistance.

2-Can be applied over intact alkyd paints.

3-Fast drying.

4-Good filling and sanding down properties.

5-Good resistant to salt water,oil splashes.

6-Easily applied by brush,roller and spray.

Physical data    

Colour:                                                       customer request

Finish:                                                        gloss

Flash point:                                               28°c

Volume solids:                                          46±2%

D.f.t:                                                            30-40 microns

Specific gravity:                                        1.3 ± 0.05gr/cm3     

Theoretical coverage:                             15.3  m2 /lit (at 30 µ d.f.t)

Drying time at 25°c:

        Touch dry :                                       4 hrs

   Dry to handle :                                      8hrs

            Full cure:                                      7 days

Component:                                             1

Application methods:                              conventional spray or brush or

                                                              Airless spray or roller

Recoat intervals*:                                 10°c                 25°c              40°c

(mild condition) :   Min:                          30  hrs            12  hrs          6  hrs

                          **Max:                          NONE             NONE         NONE

**Maximum Recoat: Unlimited. Must have a clean, dry surface for top coating.”Loose” chalk or salts must be removed in              .        accordance with good painting practice. Drying time is temperature, humidity, and fi lm thickness dependent

Recommended thinner:                         RANA THINN 70

Recommended cleaner:                        RANA CLEAN 70

Shelf life:                                                   12 months when stored indoors in unopened

Original containers at 5 to 40°c (cool and dry


Curing mechanism:                                by solvent release and chemical reaction with  o2

Substrate:                                              primed steel

 *: For recoating the surface should be free of dust ,grease  and contamination .

    Typical uses

As a general purpose finishing coat ,interior and

exterior ,on decks ,stairways ,cat walks, etc;

In mildly to moderately corrosive environment.

Application information

This RANA CHEM’s product is an alkyd based coating

for industrial and marine use.

To obtain the maximum performance for which this product

is formulated,strict adherence to all application,instructions,

precautions,conditions and limitations is necessary.

Application equipment

The following equipment is listed as a guide and suitable

equipment from other manufactures may be used.

Adjustments of pressure and change of tip size may be

needed to obtain the proper spray characteristics.

1-Airless spray:standard airless spray equipment having

a 28:1 or higher pump ratio and a  fluid tip with a 0.28 to 0.33 mm


2-Conventional spray:industrial equipment such with suitable

aircap having  a fluid tip with a 1.4-1.6mm orifice .




1-Handle with care.

2-Avoid inhalation of possible solvent vapours or

paint mist,as well as paint contact with skin and eyes.

3-Apply only in well ventilated areas and ensure that

adequate forced ventilation exists when applying paint

In confined spaces or when the air is stagnant.


 4-Always take precautions against the risks of fire

 and explosions.

5-Don’t empty into drains and take precautionary measures

      against static discharges.

6-Harmful or fatal if swallowed,immediately seek medical


Application procedure

1-Flush equipment with recommended cleaner before use.

2-Stir paint  for 5 minutes.

3-For spray,thin only as needed for workability.

 4-Apply a wet coat in even, parallel passes.overlap

 each pass 50% to avoid bare areas,pinholes or holidays.

5-Small damaged or bare areas and random pinholes or

holidays can be touched up by brush.

6-Clean all equipment with recommended cleaner

immediately after use.

Environmental condition

      Environmental temperature must be 10-40°c.

      Surface temperature must be at least 3°c above dew point

      to prevent condensation. At freezing temperature surface

      must be free of ice and relative humidity below  80 %.

Surface preparation

The surface must be clean and dry .all dirt, grease and other

foreign materials ` should be removed .old primed surface

must be smoothly wire brushed.

No Comments

Sorry, the comment form is closed at this time.