|   EPOXY AMIDE RANA   |   No comment
رنگ ضد حریق


    RANA 801 P

Product information

1-Poly amide epoxy primer.

2-Suitable for variety of substrates.

3-Excellent rust inhibitive shop primer in corrosive environments.

4-Excellent resistant with a suitable topcoat to water, chemicals

   and petroleum products.

Physical data    

Color:                                                         customer request

Finish:                                                        Flat

Flash point:

           Resin:                                            34°c

           Cure:                                             36°c

           Solvent:                                         28°c

Volume solids:                                          58±2%

D.F.T:                                                         60-70  microns

Specific gravity(mixed):                          1. 67±  0.05gr/cm3  

Theoretical coverage:                             9.6 m2 /lit (at 60 µ D.F.T)

Drying time at 25°c:

                Touch dry:                               3 hrs

          Dry to handle:                               6-8 hrs

                  Full cure:                               7 days

Component:                                             2

Pot life:                                                      6-8 hrs at 25 °c:

Mixing ratio(by volume):

                                    Resin:                refer to can label

                                    Cure:                  refer to can label

Application methods:                              conventional spray or brush or

                                                              Airless spray or roller

Recoat intervals* :                                10°c                 25°c               40°c

(mild condition) :   Min:                         25  hrs            12  hrs           5  hrs

                          **Max:                         NONE             NONE         NONE

**Maximum Recoat: Unlimited. Must have a clean, dry surface for top coating.”Loose” chalk or salts must be removed in              .        accordance with good painting practice. Drying time is temperature, humidity, and fi lm thickness dependent

Recommended thinner:                          RANA THINN 80

Recommended cleaner:                         RANA CLEAN 80

Shelf life:                                                   12 months when stored indoors in unopened

Original containers at 5 to 40°c (cool and dry


Curing mechanism:                                by solvent release and reaction by

                                                                    Curing  agent and resin

 RANA 801 P

Typical uses

1-As a maintenance and repair primer coat in moderate

to severely corrosive environment.

2-As a high performance coating for marine and industrial

facilities, ballast and potable water tanks, bilges,

and draining pipes, above and bellow water hulls.

Application equipment

The following equipment is listed as a guide and suitable

equipment from other manufactures may be used.

adjustments of pressure and change of tip size may be

needed to obtain the proper spray characteristics.

1-Airless spray:

2-Conventional spray:

3 -Mixer:mixer must be powered by an air motor or an explosion

proof electric motor.

4-Brush or roller.

Application procedures    

1-Flush  equipment with cleaner before use.

2-Stir resin to an even consistency with a power mixer.

3-Add cure to resin and continue stirring for 5 minutes.

Note:since the pot life is limited and shortened by high

temperatures ,do not mix more material than will be used

in 8 hours at 25 °c.

4- Thinning  with RANA THINN 80 for necessary

5-Stir during application to maintain uniformity of material

and apply a wet coat in even parallel passes after 20 minutes.

6-Clean all equipment with cleaner immediately after use.

RANA 801 P

Environmental condition

      Environmental temperature must be 10-40°c.

      Surface temperature must be at least 3°c above dew point

      to prevent condensation. At freezing temperature surface

      must be free of ice and relative humidity below 80 %.

Surface preparation

Sand blasting to standard  Sa 2.5 – Sa3 , SIS 05 5900 , ISO 8501-1.

No Comments

Sorry, the comment form is closed at this time.