Blog

M.I.O EPOXY I – RANA 829 I

  |   EPOXY AMIDE RANA   |   No comment
رنگ ضد حریق

EN.TDS

Product information 

1-Good adhesion to properly pretreated galvanized steel.

2-Can be used in systems for atmospheric or water

immersed exposure conditions.

3-Good abrasion and impact resistance.

4-Good adhesion characteristics for subsequent coats.

5-Good resistance to industrial or chemical contaminated

atmospheric exposure conditions.

Physical data    

Colour:                                                       grey

Finish:                                                        Flat

Flash point:

           Resin:                                            34°c

           Cure:                                             36°c

           Solvent:                                         28°c

Volume solids:                                          57±2%

D.F.T:                                                         100-150  microns

Specific gravity(mixed):                          1.65±  0.05gr/cm3   

Theoretical coverage:                             6 m2 /lit (at 100 µ D.F.T)

Drying time at 25°c:

                Touch dry:                               2 hrs

        Dry to handle:                                 6-8 hrs

                 Full cure:                                7 days

Component:                                             2

Pot life:                                                      8  hrs at 25 °c:

Mixing ratio(by volume):

                                    Resin:                refer to can label

                                    Cure:                  refer to can label

Application methods:                              conventional spray or brush or

                                                              Airless spray or roller

Recoat intervals* :                               10°c                   25°c             40°c

(mild condition) :  Min:                          25  hrs              12  hrs         5  hrs

ZINC RICH EPOXY PRIMER2 - RANA 802P & 802P1
مطالعه

                      **Max:                          NONE             NONE         NONE

**Maximum Recoat: Unlimited. Must have a clean, dry surface for top coating.”Loose” chalk or salts must be removed in              .        accordance with good painting practice. Drying time is temperature, humidity, and fi lm thickness dependent

Recommended thinner:                          RANA THINN 80

       Recommended cleaner:                         RANA CLEAN 80

       Shelf life:                                                   one year when stored indoors unopened

Original containers at 5 to 40°c (dry and cool  place)

*: For recoating the surface should be free of dust ,grease  and contamination .

 

Curing mechanism:                                by solvent release and reaction by

                                                                    Curing agent and resin

Substrate:                                                 steel ,primed steel, galvanized steel

Typical uses

1-Zinc rich primed steel parts.

2-Galvanized steel sheets.

3-Steel

4-Shop primed steel.

Application information

This RANA CHEM’s product is a micaceous iron oxide

coating for industrial and marine use.

To obtain the maximum performance for which this product

is formulated,strict adherence to all application,instructions,

precautions,conditions and limitations is necessary.

Application equipment

The following equipment is listed as a guide and suitable

EPOXY INTERMEDIATE COAT HB - RANA 823 I HB
مطالعه

equipment from other manufactures may be used.

Adjustments of pressure and change of tip size may be

Needed to obtain the proper spray characteristics.

1-Airless spray:standard airless spray equipment having

a 28:1 or higher pump ratio and a  fluid tip with a 0.457 to 0.660 mm

orifice.

2-Conventional spray:industrial equipment with suitable

aircap having  a fluid tip with a 2 – 2.2 mm orifice .

3 -Mixer: mixer must be powered by an air motor or an explosion

proof electric motor.

4-Brush or roller.

Caution

 

1-Handle with care.

2-Avoid inhalation of possible solvent vapours or

paint mist,as well as paint contact with skin and eyes.

3-Apply only in well ventilated areas and ensure that

adequate forced ventilation exists when paint applies is in

confined spaces or when the air is stagnant.

4-Always take precautions against the risks of fire

and explosions.

6-Harmful or fatal if swallowed,immediately seek medical

assistance.

7-Use fresh air masks and explosion proof equipment.

EPOXY INTERMEDIATE COAT HB BS 6920 SPECIAL - RANA 823 I HB
مطالعه

Application procedures    

1-Flush  equipment with cleaner before use.

2-Stir resin to an even consistency with a power mixer.

3-Add cure to resin and continue stirring for 5 minutes.

Note: Since the pot life is limited and shortened by high

temperatures ,do not mix more material than will be used

in 6 hours at 25 °c.

4-Thinning  with RANA THINN 80 as needed for workability.

5-Stir during application to maintain uniformity of material

and apply a wet coat in even parallel passes after 20 minutes.

6-Clean all equipment with cleaner immediately after use.

Environmental condition

      Environmental temperature must be 10-40°c.

      Surface temperature must be at least 3°c above dew point

      to prevent condensation. At freezing temperature surface

      must be free of ice and relative humidity below 80 %.

Surface preparation

The surface must be clean and dry .All dirt grease and other

foreign  materials  should be removed .Old primed surface must

be smoothly wire brushed.

No Comments

Sorry, the comment form is closed at this time.