|   alkyd paint rana   |   No comment
رنگ ضد حریق



       RANA 715 P

Product information 

1-Excellent spray ability

2-Resists corrosion.

3-Recommended for use on steel where a conventional

topcoat system is required.

4-High resistance in mildly to moderately corrosion environment.

Physical data    

Colour:                                                       Orange

Finish:                                                        Flat

Flash point:                                               24°c

Volume solids:                                          55±2%

D.f.t:                                                            50-75  microns

Specific gravity:                                        1.5 ±  0.05gr/cm3    

Theoretical coverage:                             4  m2 /lit (at 50 µ d.f.t)

Drying time at 25°c:

                touch dry:                                2hr

        dry to handle:                                  6hrs

                 full cure:                                 7days

Component:                                             1

Application methods:                              Conventional spray or brush or

                                                              airless spray or roller

Recoat intervals*:                                 10°c                 25°c              40°c

(mild condition) :   Min:                          30  hrs            12  hrs          6  hrs

                       **Max:                          NONE             NONE         NONE

**Maximum Recoat: Unlimited. Must have a clean, dry surface for top coating.”Loose” chalk or salts must be removed in              .        accordance with good painting practice. Drying time is temperature, humidity, and fi lm thickness dependent

Recommended thinner:                         RANA THINN 70

Recommended cleaner:                        RANA CLEAN 70

Shelf life:                                                   12 months when stored indoors in unopened

Original containers at 5 to 40°c (cool and dry


Curing mechanism:                                By solvent release and chemical reaction with  o2

Substrate:                                               Steel

*: For recoating the surface should be free of dust ,grease  and contamination



  RANA 715 P

Typical uses

As a primer on interior and exterior steel in

mildly to moderately corrosive environment.

Application information

This RANA CHEM product is a red lead alkyd primer

for above water service.

To obtain the maximum performance for which this product

is formulated,strict adherence to all application,instructions,

precautions,conditions and limitations is necessary.

Application equipment

The following equipment is listed as a guide and suitable

equipment from other manufactures may be used.

Adjustments of pressure and change of tip size may be

needed to obtain the proper spray characteristics.

1-Airless spray:standard airless spray equipment having

A 28:1 or higher pump ratio and a  fluid tip with a 0.33 to 0.381 mm


2-Conventional spray:industrial equipment with suitable

aircap having  a fluid tip with a 1.8 – 2 mm orifice .

3 -Mixer:mixer must be powered by an air motor or an explosion

proof electric motor.

4-Brush or roller.

 RANA 715 P
Application procedure

1-Flush equipment with recommended cleaner before use.

2-Stir paint  for 5 minutes.

3-For spray,thin only as needed for workability.

4-Apply a wet coat in even, parallel passes.overlap

each pass 50% to avoid bare areas,pinholes or holidays.

5-Small damaged or bare areas and random pinholes or

holidays can be touched up by brush.

6-Clean all equipment with recommended cleaner

immediately after use.

Environmental condition

      Environmental temperature must be 10-40°c.

      Surface temperature must be at least 3°c above dew point

      to prevent condensation. At freezing temperature surface

      must be free of ice and relative humidity below  80 %.

Surface preparation

The surface must be clean and dry . All dirt , grease ,

millscale and any other foreign material should be

removed.sand blasting or wire brushing to a standard

of St2 ,Sa 2.5 – Sa3 , SIS 05 5900 , ISO 8501-1.

No Comments

Sorry, the comment form is closed at this time.